Question: What Is 1/10 On A Tape Measure?

What is .8 as a fraction?

Decimal to fraction conversion tableDecimalFraction0.84/50.833333335/60.857142866/70.8757/845 more rows.

What is 1/10 on a tape measure?

If a ruler has no legend the smallest graduation of an inch will have to be calculated. Simply count the number of spaces between graduations or marks contained within a single inch. If there are 10 the smallest graduation or mark is 1/10” or 0.1” as a decimal.

What is .3 of an inch in fraction?

Inch Fraction Conversion Chart – Fraction Decimal and Metric EquivalentsFraction (inches)Decimal (inches)Metric (millimeters)11/32″0.34375″8.73125 mm23/64″0.359375″9.128125 mm3/8″0.375″9.525 mm25/64″0.390625″9.921875 mm60 more rows

What is a tenth on a ruler?

Convert your inches to tenths, keeping in mind that a tenth is one tenth of a foot, which is 12 inches–a tenth, therefore, is 12/10 or 1.2 inches. If you measure your water heater’s circumference as 144 inches, for example, you can convert it to tenths as follows: 144/1.2 = 120 tenths.

How much is a tenth of an inch on a ruler?

If you have 1/32 inch markings, 3/32nds is just over 1/10th inch it might be accurate enough for your purposes. Or use a metric ruler, 25.4 mm is one inch, so 2.5mm is about 1/10th of an inch.

How big is an inch on your finger?

The length between your thumb tip and the top knuckle of your thumb is roughly one inch.

What is .2 of an inch on a ruler?

Learn the 1/2 inch marks. The 1/2 inch marks will be the second longest lines on the ruler, half as long as the inch marks. Each 1/2 inch mark will come midway between each inch number because it is half of an inch.

How do you read a tenth ruler?

Read along the ruler, starting at the “zero” mark, until you reach the far edge of whatever you’re measuring. Note where that edge falls between the centimeter marks (the large, numbered marks on the tenths or metric side of any ruler).

What comes after a half on a ruler?

The markings on a standard ruler represent the fractions of an inch. The markings on a ruler from the start to the 1″ mark are: 1⁄16“, 1⁄8“, 3⁄16“, 1⁄4“, 5⁄16“, 3⁄8“, 7⁄16“, 1⁄2“, 9⁄16“, 5⁄8“, 11⁄16“, 3⁄4“, 13⁄16“, 7⁄8“, 15⁄16“, and 1”.

What is 3/4 as a decimal?

Fraction to Decimal Conversion Tablesfraction = decimal1/2 = 0.51/3 = 0.32/3 = 0.61/4 = 0.253/4 = 0.751/5 = 0.22/5 = 0.43/5 = 0.619 more rows

What is .067 as a fraction?

getcalc.com’s decimal to fraction calculator to find what’s an equivalent fraction for the decimal point number 0.067 or 6.7%….How to Write 0.067 or 6.7% as a Fraction?DecimalFractionPercentage0.06969/10006.9%0.06868/10006.8%0.06767/10006.7%0.06666/10006.6%5 more rows

What does 1/8th of an inch look like?

What does 1/8 of an inch look like on a ruler? The 1/8 of an inch marks are the smaller marks found directly in between the 1/4 of an inch marks on the ruler. Between 0 and 1 inch, there are marks that denote 1/8, 1/4 (or 2/8), 3/8, 1/2 (or 4/8), 5/8, 6/8 (or 3/4), 7/8, and 1 (or 8/8) of an inch.

What is 1/10th of an inch?

There are 10 tenths of an inch in one inch. As one inch equals 2.54 centimeters, one tenth of an inch equals 0.254 centimeters. In some contexts, a tenth of an inch can also be referred to as a line.

What is 7/10 of an inch on a ruler?

11.2 sixteenthsSo 11.2 sixteenths of an inch is equal to 7/10 of an inch.

How do you find 1/10 of a number?

To find one tenth of a number, simply divide it by 10 . The easiest way to do that is to : cross off a zero at the end if there is one. move the decimal one place to the left.

How much is a tenth?

One tenth is the same as one out of ten parts. It is a common fraction that means the same as 10% or 0.1.

How many cm are in a ruler?

30 cmThe standard metric ruler is 30 cm long. Each centimeter is labeled with a number to show the measurement it’s referring to. You might see inches on the other side of your metric ruler. In this case, refer to the instructions above to learn how to read a ruler in inches.